Do you want to learn how to remove water saver from shower head? If your shower head has a water saver you most likely know how this can become annoying sometimes. Although the flow restrictor is a great water-saving idea, it can make your shower nightmarishly slow and transform a perfect shower head spray to a slow trickle of a shower, especially when you are living in an area with low water pressure. It is hard to enjoy a chic shower or rinse your body properly in such a scenario.
If your shower flow is weak, read on to discover the handy method in this post. Before diving into the workaround, let’s find out what exactly it is and where it is located.
- What is a Flow Restrictor after all?
- How to Remove the Water Saver from A Shower Head?
- Things to Consider While Removing Water Saver
What is a Flow Restrictor after all?
A flow restrictor, also referred to as a water saver or water restrictor, is a device installed in your shower head that does just what it says; it restricts or reduces the amount and flow of water that comes from your shower head, which as a result saves your water bill while preventing water wastage during shower time. According to professionals, water restrictors reduce the amount of water that flows from your shower head to less than two and a half gallons per minute.
Where is the water saver then? Can you see it from where your shower head screws off of the bathroom pipe coming from the wall, or at the end of the flexible hose of your hand-held shower head? That annoying restrictor is installed right behind there! You will notice a flat, circular device made of plastic whose center is star-shaped and may come in a different color from the rest of the apparatus. There it is!
How to Remove the Water Saver from A Shower Head?
Removing the shower head water flow restrictor means that your water flow will not be controlled, which translates to more expenditure on utility bills. However, there is nothing as nice as enjoying a good shower moment, whether alone or in the company of your spouse. Do not let a showerhead water flow restrictor come in between you and your precious moment of joy. Learn how to remove flow restrictor from shower head by following this detailed guideline.
Tools You May Need
Before you start removing that annoying water saver, make sure that you have all the tools that you will need. Fortunately, you may already have them at home.
- Clean rag
- Flathead screwdriver
- Needle-nose pliers
- Paper clips
- Pipe or adjustable wrench
- Teflon (plumber’s tape)
Steps on How to Remove Water Saver from Shower Head
Note that most modern shower heads, like the Declinko shower heads, are designed with threads for installation. Pay attention not to damage these threads, otherwise, it will become impossible to re-install or adjust.
Step 1: Turn off the water and remove the shower head from the bathroom water pipe
Turn off the shower water from the main supply. Using a clean cloth rag to wrap in order to protect the shower head connector, unscrew the nut using a wrench by turning it anticlockwise.
Step 2: Snoop off the filter screen
Can you see the filter screen in your showerhead? It is usually at the end of the shower head handle, used to prevent debris from entering your shower head.
Using a pair of needle-nose pliers, pry off the filter screen carefully. You can also remove it by softly tapping on your shower head to dislodge it.
Step 3: Remove the O-ring
After removing the filter screen, you need to remove the O-ring, a black gasket that you should carefully remove using a paper clip or needle-nose pliers. Wrap the O-ring with a damp cloth to prevent it from drying out for later re-installation.
Step 4: Remove water saver from the shower head
I suppose you should be able to locate the restrictor with ease after reading this article. In this way, you need to pull, prop, pop, or pry it out of the shower head.
Step 5: Reinstall the O-ring
Make sure you do not forget to put it back in the O-ring. Otherwise, your shower apparatus will leak sending water out thereby making your bathroom a swimming pool. Using tweezers, place the O-ring back to where you had removed it. Apply slight pressure to ensure that it fits properly.
Step 6: Reinstall the filter screen
Reinstall the filter screen back to where it was using tweezers.
Step 7: Replace the plumber’s tape on the bathroom water pipe and screw back the shower head
Note that whether or not there was a plumber’s tape on the bathroom water pipe, you should place a new layer of it. This serves to ensure that you have screwed back your shower head tightly on the bathroom water pipe and prevent any leaks on the apparatus.
Things to Consider While Removing Water Saver
- Take care not to damage the filter screen in the process since replacing it is usually difficult.
- If your filter screen has accumulated dirt, use warm water and detergent to clean it, and then set it aside carefully.
- Check the O-ring to determine whether it has any tears, punctures, or cracks. Get a replacement if damaged.
- Be careful not to break or move the bathroom shower pipe that is attached to the wall.
The basic and primary intention of the water restrictor is to conserve water by limiting the amount that flows through your shower head. However, in cases where the water pressure is low or your shower head is experiencing thin drizzles, the water restrictor can work to your disadvantage. This is why you need to learn how to remove water saver from shower head by following the simple guidelines above, with which you can now reclaim your lost shower glory.
FAQs on How to Remove Water Saver from Shower Head
This is a question that many people ask. Whether to remove shower head water flow restrictor depends on personal circumstances and choices. If you are suffering from a slow flow of water or thin drizzles on your shower head, it is time to learn how to remove flow restrictor from shower head and transform your bathing moments into normal bliss.
Yes. Removing the restrictor means that you will be unable to conserve water which is scarce. Besides, using more water means spending more on utility bills. And you may damage the shower head with the improper operation.
No. Some shower heads do not have water savers installed. However, you should expect that most new and modern shower heads will have water restrictors preinstalled.
0 Comments for “Discover How to Remove Water Saver from Shower Head”